Why 1990s Hardboard Siding in Tomball Is Failing Now
A lot of the two-story brick-and-hardboard houses built around Tomball in the 1990s — the early phases of neighborhoods like Lakewood Forest, plus scattered infill closer to Old Town — used hardboard lap siding above the brick veneer on the gable ends and second story. It looked fine for twenty-some years. Now it's past its expected service life, and the Gulf Coast humidity has been working on it the whole time. Hardboard is wood fiber held together with resin, and once moisture gets past the paint film and into the edges, it swells, delaminates, and starts to crumble. Twenty-plus hail seasons — including repeat hits in April, which is Tomball's reliable hail month — have also chipped away at the paint and caulk joints that were protecting it.
If you're not sure how old your siding actually is, the Harris County Appraisal District's year-built record for the house is a more reliable starting point than guessing from memory or a neighbor's story.
What to Look For: Drip Edge Swelling, Kick-Out Flashing, and Profile Matching
Three things come up over and over on these inspections:
- Swelling at the drip edge. The bottom edge of each hardboard course is the most exposed spot on the wall. Look for a soft, puffy ridge along the bottom of the boards, especially under windows and near the roofline — that's the fiber swelling from trapped water, and it spreads if left alone.
- Missing or undersized kick-out flashing. Where a roofline meets a wall — common where the garage roof or a lower porch roof ties into the second story — water needs a small diverter flashing to kick it away from the siding and into the gutter instead of running down behind the wall. A lot of 1990s builds skipped it or installed it too small. If you see a dark water-stain streak running down the siding right at a roof-to-wall intersection, that's usually the giveaway.
- Profile matching. Hardboard lap siding comes in specific exposure widths and groove patterns, and most of the original 1990s profiles are no longer made. Patching a damaged section with a close-but-not-quite board is one of the more common cosmetic mistakes homeowners end up living with — it's worth getting this right the first time rather than redoing it.
A proper look at the whole wall system, not just the obviously damaged boards, is really the job of a siding and trim inspection, since swelling at one corner is often a sign of water getting in somewhere less visible.
Permits Before You Start
If your house is inside the Tomball city limits, re-siding generally runs through the same permit process as other exterior work handled by the Building Office at 501 James St (281-290-1402). The residential permit fee itself is modest — around $50 — but the paperwork matters: the contractor needs to carry at least $500,000 in combined single-limit liability coverage with the City listed as certificate holder, the permit is void if work doesn't start within six months, and starting without one means paying double fees after the fact.
If your home sits in unincorporated Harris County instead — which covers a lot of the subdivisions around Tomball — the county's Office of Code Enforcement says a permit is needed for development generally, but whether a re-siding job specifically triggers that requirement isn't something we can confirm from here. Call Harris County Residential Permits at (713) 274-3900 and ask directly before work starts. Homes in Magnolia go through a separate process that includes contractor registration — reach that office at 281-356-2266 x7.
- Confirm whether your address is inside Tomball city limits, unincorporated Harris County, or Magnolia.
- Call the relevant permit office before scheduling any work.
- Get the siding damage documented and the extent of the problem mapped out, not just the obvious boards.
- Choose a replacement profile and material before demo starts, so there's no gap between tear-off and new installation.
- Schedule the swap for a dry stretch — hardboard removal exposes the wall sheathing, and Tomball's spring storms aren't something you want timing against.
Choosing a Replacement Material
Most homeowners doing this now move to fiber cement rather than replacing hardboard with hardboard. It holds paint longer, doesn't swell the same way at cut edges, and handles our humidity and hail better over time. The tradeoff is weight and cutting technique, which is why profile matching really does need an installer who's done fiber cement over brick veneer before — not just panel siding on a slab home. You can see the range of options on the fiber cement siding page, including how boards are typically matched to an existing brick line and trim reveal. If your gutters or kick-out flashing also need attention while the wall is open — which is common — it's worth handling at the same time rather than opening the wall twice.
The bottom line: on a 1990s Tomball two-story, swelling at the drip edge is rarely an isolated spot repair — it's a sign the whole wall system is due, and getting the permit and the profile right the first time saves you from doing this job twice.
Tomball Roofing